Chapter 4 Batteries with Terminals and Soldering Lithium Batteries Chapter 4 Batteries with Terminals .78 Soldering .78 Chapter 3 Batteries with Terminals
obviating eliminating the need for reinforcement or other
Highly Reliable Terminal Welding
Panasonic adopted the laser welding method to solder
The tips of the terminals are pre-soldered in order to
battery terminal onto the printed circuit board.
enhance the reliability of the soldering.
In the comparison of 20 series battery, while the ten-
sile strength of conventional resistance welding method
was 20-50N (about 2 to 5 kgf), laser welding method
was 100N (about 10kgf) and the variations was comp-
Complete Line-up
By using the laser welding method, terminal welding on
a thin battery (1.4mm in thickness) is able to perform.
Panasonic offers a full range of batteries with terminals
Since strengthening the welding etc. became unneces-
for PCB mounting. Since the terminals come in a vari-
sary, battery could be widely used to many applications.
ety of types, please contact Panasonic for further de-
tails. A more limited selection of simple battery holders
to support the batteries is also available. Soldering Cautions
Do not allow the soldering iron to make direct contact
with the bodies of the batteries. Proceed with the sol-
dering quickly within 5 seconds while maintaining the
Example where the terminals were soldered straight onto acoin-type lithium battery, the terminals were connected to a
Chapter 4
iron tip temperature at about 350°C, and do not allow
PC board or other electronic components, and the heat gen-erated by the soldering adversely affected the battery, result-
the temperature of the battery bodies to exceed 85°C.
ing in a deterioration of the battery characteristics:
The heat generated when terminals are mounted using
Soldering with a dip-soldering bath can be used by con-
dition but do not allow the temperature of the battery bo-
The separator melts and becomes perforated.
°C. It is important to note, depending on
the temperature conditions inside the dipping device,that
the battery body temperature may rise after dipping due
The positive and negative poles are welded together,
Batteries with T
to the residual heat retained. When a post-dipping te-
mperature rise is observed, review the temperature co-
nditions and consider a dipping time reduction or a way
In terms of the battery characteristics, the open-circuit
of forcibly cooling the batteries after dipping.
voltage and electrical capacity are both reduced. Basic conditions erminals and Soldering
The battery loses its functions or it bursts in rare cases. Never Use Reflow Soldering
Please do not carry out re-flow welding except for there-flow corresponding batteries (ML-R and NBL-R).
Never use reflow soldering since doing so directly heats
the battery surface to high temperatures, causing ele- ctrolyte leakage, deterioration of battery characteris-
(note 1)Metal whose melting point is about 180°C
tics and risking bursting or ignition.
(note 2)Non woven cloth of polypropylene whose melting point is about
Chapter 3
APO-SALBUTAMOL INHALER NAME OF THE MEDICINE Chemical Name: RS)-2-tert-butylamino-1-(4-hydroxy-3-hydroxymethyl-phenyl) ethanol sulfate. C13H21NO3.½ H2SO4 Structural Formula: CAS Registry Number: 51022-70-9 DESCRIPTION Salbutamol sulfate is a white or almost white powder. It is soluble in water but is only slightly soluble in alcohol, chloroform and ether. 1.2mg of s
Biology 697: Introduction to Computational Data AnalysisWelcome to your mid-term! I hope you enjoy. Note, in all of the questionsbelow, there are easy not so code intensive ways of doing it, and there are longermore involved, yet still workable ways to answer them. I would suggest thatbefore you dive into analyses, you do the following. First, breathe. Second,think about the steps you need to ex
Chapter 4
Batteries with Terminals