Microsoft word - 1009-02 maxsignal® beta-agonist elisa test kit manual

BIOO FOOD AND FEED SAFETY
Beta-Agonist ELISA Test Kit Manual
Catalog #: 1009
Reference #: 1009-02
TABLE OF CONTENTS
GENERAL INFORMATION . 1
Product Description . 1 Procedure Overview. 1 Kit Contents, Storage and Shelf Life . 2 Sensitivity (Detection Limit). 2 Specificity (Cross-Reactivity) . 3 Required Materials Not Provided With the Kit . 3 Warnings and Precautions . 4 SAMPLE PREPARATION . 5
Feed. 5 Meat/Liver/Kidney . 6 Milk. 6 Urine . 6 BETA-AGONIST ELISA TEST KIT PROTOCOL . 7
Reagent Preparation . 7 ELISA Testing Protocol. 7 Beta-Agonist Concentration Calculations . 8 TROUBLESHOOTING . 9
No Color Development or No Signals with Standards. 9 Low Optical Density (OD) Readings. 9 High Background or High Optical Density (OD) Readings . 9 High Intra-Plate Variance. 10 High Inter-Plate Variance . 10 One or More of the Standard Curve Points Are Out of Range. 10 MaxSignal® Beta-Agonist ELISA Test Kit is intended for laboratory use only, unless otherwise indicated. This product is NOT for clinical diagnostic use. MaxSignal is a registered trademark of Bioo Scientific Corporation (BIOO). MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 GENERAL INFORMATION
GENERAL INFORMATION

Product Description

MaxSignal® Beta-Agonist ELISA Test Kit is a competitive enzyme immunoassay for the quantitative analysis of clenbuterol, salbutamol, bitolterol, carbuterol and other related beta-agonists in feed, meat/liver/kidney, milk and urine. Beta-agonists can improve the meat/fat ratio in fattened animals and accelerate livestock growth. They also have a relaxing effect on non-striated musculature and can be used as antiasthmatic and tocolytic agents in human beings. Therefore, excess beta-agonist residues in livestock products may lead to health risks for consumers. This has led to a prohibition of beta-agonist use in food production. The amount of beta-agonist residues can be determined by methods such as HPLC or GC-MS. However, these traditional methods usually require very expensive preparation procedures. Alternatively, enzyme immunoassay (ELISA) can be used as a screening system, which is simple, rapid, sensitive and cost-effective compared with traditional methods. MaxSignal® Beta-Agonist ELISA Test Kit enables international and government regulatory agencies, food manufacturers and processors, as well as quality assurance organizations, to detect beta-agonist residues in various sample types in response to customer concerns about food safety. The unique features of the kit are: Providing a rapid (10 - 30 minutes) and extraction method for various samples with high High sensitivity (0.05 ng/g or ppb) and low detection limit (0.025 ng/g or ppb for meat/tissue, 0.05 ng/g or ppb for urine and 0.2 ng/g or ppb for feed). A quick ELISA assay (less than 2 hours regardless of number of samples). High reproducibility.
Procedure Overview
The method is based on a competitive colorimetric ELISA assay. The drug of interest has been coated in the plate wells. During the analysis, sample is added along with the primary antibody specific for the target drug. If the target is present in the sample, it will compete for the antibody, thereby preventing the antibody from binding to the drug attached to the well. The secondary antibody, tagged with a peroxidase enzyme, targets the primary antibody that is complexed to the drug coated on the plate wells. The resulting color intensity, after addition of substrate, has an inverse relationship with the target concentration in the sample. BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 1 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 Kit Contents, Storage and Shelf Life
MaxSignal® Beta-Agonist ELISA Test Kit has the capacity for 96 determinations or testing of 42 samples in duplicate (assuming 12 wells for standards). Return any unused microwells to the foil bag and reseal them with the desiccant provided in the original package. Store the kit at 2-8°C *. The shelf life is 12 months when the kit is properly stored. Contents Amount Storage
Negative control (white cap tube) 0.8 mL 0.05 ng/mL (yellow cap tube) 0.8 mL 0.15 ng/mL (orange cap tube) 0.8 mL 1.5 ng/mL (purple cap tube) 0.8 mL 10 ng/mL (spiking, optional, red cap tube) 0.8 mL * If you are not planning to use the kit for over 3 months, store Beta-Agonist Antibody #1 and 100X HRP-Conjugated Antibody #2 at -20°C or in a freezer. Components with the same BIOO part No’s within their expiration dates are interchangeable among BIOO kits.
Sensitivity (Detection Limit)
Meat/Liver/Kidney *
ß-Agonists
* Based on Organic Reagent Extraction Method. ** Based on Rapid Extraction Method. BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 2 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 Specificity (Cross-Reactivity)
Beta-Agonists Cross-Reactivity

Required Materials Not Provided With the Kit

Microtiter plate reader (450 nm) Incubator Tissue Mixer (e.g. Omni TissueMaster Homogenizer) Rotary evaporator or nitrogen gas Vortex mixer (e.g. Gneie Vortex mixer from VWR) 10, 20, 100 and 1000 µL pipettes Multi-channel pipette: 50-300 µL (Optional) BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 3 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 Warnings and Precautions
BIOO strongly recommends that you read the following warnings and precautions to ensure your full awareness of ELISA techniques and other details you should pay close attention to when running the assays. More information can also be found in Troubleshooting section. Periodically, optimizations and revisions are made to the kit and manual. Therefore, it is important to follow the protocol coming with the kit. If you need further assistance, you may contact your local distributor or BIOO at techsupport@biooscientific.com. The standards contain clenbuterol. Handle with particular care. Do not use the kit past the expiration date. Do not intermix reagents from different kits or lots except for components with the same part No’s within their expiration dates. ANTIBODIES AND PLATES ARE KIT-AND LOT-SPECIFIC. Make sure that the antibody #2 and diluent are mixed in correct volumes. Try to maintain a laboratory temperature of 20°–25°C (68°–77°F). Avoid running assays under or near air vents, as this may cause excessive cooling, heating and/or evaporation. Also, do not run assays in direct sunlight, as this may cause excessive heat and evaporation. Cold bench tops should be avoided by placing several layers of paper towel or some other insulation material under the assay plates during incubation. Make sure you are using only distilled or deionized water since water quality is very When pipetting samples or reagents into an empty microtiter plate, place the pipette tips in the lower corner of the well, making contact with the plastic. Incubations of assay plates should be timed as precisely as possible. Be consistent when adding standards to the assay plate. Add your standards first and then your samples. Add standards to plate only in the order from low concentration to high concentration as this will minimize the risk of compromising the standard curve. Always refrigerate plates in sealed bags with a desiccant to maintain stability. Prevent condensation from forming on plates by allowing them equilibrate to room temperature (20 – 25°C / 68 – 77°F) while in the packaging. BIOO makes no warranty of any kind, either expressed or implied, except that the materials from which its products are made are of standard quality. There is no warranty of merchantability of this product, or of the fitness of the product for any purpose. BIOO shall not be liable for any damages, including special or consequential damage, or expense arising directly or indirectly from the use of this product. BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 4 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 SAMPLE PREPARATION
SAMPLE PREPARATION
Be sure samples are properly stored. In general, samples should be refrigerated at 2-4°C for no more than 1-2 days. Freeze samples to a minimum of -20°C if they need to be stored for a longer period. Frozen samples can be thawed at room temperature (20 – 25°C / 68 – 77°F) or in a refrigerator before use. 1. Preparation of 1X Sample Extraction
Mix 1 volume of 200X Sample Extraction Buffer with 199 volumes of distilled water.
2. Preparation of 1X PBS
Mix 1 volume of the 10X PBS with 9 volumes of distilled water. Rapid Extraction Method*
(*This procedure is not recommended for tests on compound feed)
1. To a reasonable amount of feed sample, add 4 times the amount of 1X Sample Extraction Buffer (e.g. 2 g of sample + 8 mL of buffer); homogenize the sample with a suitable mixer. 2. Take out 1.5 mL of the homogenized sample and centrifuge for 5 minutes at 4,000 x g at room temperature (20 – 25°C / 68 – 77°F). 3. Carefully transfer 0.5 mL of the supernatant to a tube. 4. Incubate the supernatant at 75°C for 5 minutes and vortex 1 minute at maximum speed. 5. Centrifuge for 5 minutes at 4,000 x g at room temperature (20 – 25°C / 68 – 77°F). 6. Transfer 0.2 mL of the supernatant to a new tube, add 5 µL of Sample Balance Buffer to Note: Dilution factor: 4.

Organic Reagent Extraction**
(**This procedure works for both general animal feed and compound feed)
1. Homogenize the feed sample with a suitable mixer. 2. Add 8 mL of acetonitrile and 1 mL of ethyl acetate to 1.5 g of the homogenized sample. 3. Centrifuge for 5 minutes at 4,000 x g at room temperature (20 – 25°C / 68 – 77°F), transfer 6 mL of the supernatant to a new tube. 4. Use a rotary evaporator to dry the sample in a 60-70°C water bath under reduced pressure. Alternatively, the sample can be dried by blowing nitrogen gas in a 60-70°C water bath. 5. Add 1 mL of hexane to dissolve the sample and then add 1 mL of 1X PBS, vortex for 1 6. Centrifuge the sample for 5 minutes at 4,000 x g. 7. Use µL of the lower aqueous layer for the assay. Note: Dilution factor: 1.
BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 5 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 Meat/Liver/Kidney

Rapid Extraction Method
1. Remove fat from meat, liver or kidney. Homogenize the sample with a suitable mixer. 2. Add 1 mL of 1X Sample Extraction Buffer to 0.5 g of the homogenized sample. Vortex for 3 minutes at maximum speed or rotorack for 20 minutes ( e.g. VWR Tube Rotator ). 3. Centrifuge for 5 minutes at 4,000 x g at room temperature (20 – 25°C / 68 – 77°F), transfer 0.5 mL of the supernatant to a new tube ()Avoid touching the fatty layer!). 4. Incubate the supernatant at 75°C for 5 minutes and vortex for 1 min at maximum speed. 5. Centrifuge for 5 minutes at 4,000 x g at room temperature (20 – 25°C / 68 – 77°F). 6. Transfer 0.2 mL of the supernatant to a new tube () Avoid touching the fatty layer!), add 5 µL of Sample Balance Buffer and mix well, use 50 µL for the assay. Note: Dilution factor: 3. To avoid high background, a known negative sample should be
prepared in parallel, subtract the negative sample result from the test sample results.
Organic Reagent Extraction Method
1. Remove fat from meat, liver or kidney. Homogenize the sample with a suitable mixer. 2. Add 8 mL of acetonitrile and 1 mL of ethyl acetate to 3 g of the homogenized sample. 3. Centrifuge for 5 minutes at 4,000 x g at room temperature (20 – 25°C / 68 – 77°F), transfer 6 mL of the supernatant to a new tube. 4. Use a rotary evaporator to dry the sample in a 60-70°C water bath under reduced pressure. Alternatively, the sample can be dried by blowing nitrogen gas in a 60-70°C water bath. 5. Add 1 mL of hexane to dissolve the sample and then add 1 mL of 1X PBS, vortex for 1 6. Leave the tube open and heat the sample at 85°C for 3 minutes () This step can be omitted if the lower aqueous layer is enough for the ELISA assay). 7. Centrifuge the sample for 5 minutes at 4,000 x g. 8. Use µL of the lower aqueous layer for the assay. Note: Dilution factor: 0.5.
1. For fat-free milk, dilute the milk sample with 1X PBS Buffer (1:4) (e.g. 20 µL of milk + 80 µL of buffer). Take 50 µL of the diluted sample per well for the assay. 2. For regular milk with fat, centrifuge the milk sample at 4,000 x g for 5 minutes, discard the upper fat layer. Dilute the sample with 1X PBS Buffer (1:4) (e. g. 20 µL of milk + 80 µL of buffer). Take 50 µL of the diluted sample per well for the assay. Note: Dilution factor: 5.

1. Centrifuge 0.5 mL of the urine sample at 4,000 x g for 5 minutes. 2. Use µL of the supernatant per well for the assay. Note: Dilution factor: 1. To avoid the high background, we recommend diluting the
sample with 1X PBS 5 fold (1:4).

Preparation protocols for samples other than above can be made available upon request.
Please contact your local distributor or write us at foodfeedsafety@biooscientific.com.
BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 6 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 BETA-AGONIST ELISA TEST KIT PROTOCOL
BETA-AGONIST ELISA TEST KIT PROTOCOL

Reagent Preparation
IMPORTANT: All reagents should be brought up to room temperature before use (1 – 2
hours at 20 – 25°C / 68 – 77°F); Make sure you read “Warnings and Precautions” section
on page 4. Solutions should be prepared just prior to ELISA test. ) All reagents should be
mixed by gently inverting or swirling prior to use. Prepare volumes that are needed for the number of wells being run. Do not return the reagents to the original stock tubes/bottles. Using disposable reservoirs when handling reagents can minimize the risk of contamination and is recommended.
1. Preparation of 1X HRP-Conjugated Antibody #2
Mix 1 volume of 100X HRP-Conjugated Antibody #2 with 99 volumes of Antibody #2 Diluent. 2. Preparation of 1X Wash Solution
Mix 1 volume of the 20X Wash Solution with 19 volumes of distilled water.
ELISA Testing Protocol
Label the individual strips that will be used and aliquot reagents as the following example: Component Volume per Reaction
24 Reactions
1. Add 50 µL of each Clenbuterol Standards in duplicate into different wells () Add standards to plate only in the order from low concentration to high concentration). µL of each sample in duplicate into different sample wells. µL of Antibody #1 and mix well by gently rocking the plate manually for 1 minute. 4. Incubate the plate for 30 minutes at room temperature (20 – 25°C / 68 – 77°F). r 5. Wash the plate 3 times with 250 µL of 1X Wash Solution. After the last wash, invert the plate and gently tap the plate dry on paper towels () Perform the next step immediately after plate washings. Do not allow the plate to air dry between working steps). 150 µL of 1X HRP-Conjugated Antibody #2. Incubate the plate for 30 minutes at room temperature (20 – 25°C / 68 – 77°F) (r ) Avoid direct sunlight and cold bench tops during the incubation. Covering the microtiter plate while incubating is recommended). 7. Wash the plate 3 times with 250 µL of 1X Wash Solution. After the last wash, invert the plate and gently tap the plate dry on paper towels () Perform the next step immediately after plate washings. Do not allow the plate to air dry between working steps). 8. Add 100 µL of TMB substrate. Time the reaction immediately after adding the substrate. Mix the solution by gently rocking the plate manually for 1 minute while incubating (r ) Do not put any substrate back to the original container to avoid any potential contamination. Any substrate solution exhibiting coloration is indicative of deterioration and should be discarded. Covering the microtiter plate while incubating is recommended). BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 7 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 9. After incubating for 15 minutes at room temperature (20 – 25°C / 68 – 77°F), add 100 µL of Stop Buffer to stop the enzyme reaction. 10. Read the plate as soon as possible following the addition of Stop Buffer on a plate reader with 450 nm wavelength () Before reading, use a lint-free wipe on the bottom of the plate to ensure no moisture or fingerprints interfere with the readings).
Beta-Agonist Concentration Calculations
A standard curve can be constructed by plotting the mean relative absorbance (%) obtained from each reference standard against its concentration in ng/mL on a logarithmic curve. Use the mean relative absorbance values for each sample to determine the corresponding concentration of the tested drug in ng/mL from the standard curve. A special program with Excel functionality, MaxSignal® ELISA Analysis Program in Excel, is available upon request to evaluate the MaxSignal® ELISA test results. Please contact your local distributor or techsupport@biooscientific.com for further information. The following figure is a typical clenbuterol standard curve. The sample detection limit and quantification limit are calculated as below. Sample detection limit = (0.05 ng/g or ppb) x (dilution factor) Sample quantification limit = (0.15 ng/g or ppb) x (dilution factor) For example, the dilution factor for meat sample is 0.5, therefore, the detection limit for meat sample is 0.025 ng/g or ppb (0.05 ng/g x dilution factor 0.5) and the quantification limit is 0.075 ng/g or ppb (0.15 ng/g x dilution factor 0.5). C le nbute rol Standard C urve
Standard ng/mL (LN)
BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 8 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 TROUBLESHOOTING TROUBLESHOOTING

No Color Development or No Signals with Standards

Possible Causes
Recommended Action
Follow the protocol carefully and repeat the assay. order or a step was skipped. Wrong antibodies were used, or Make sure that the antibodies used are the ones that came with the kit. All antibodies are kit- and lot-specific. Make sure that the antibody #2 and diluent
Low Optical Density (OD) Readings

Possible Causes
Recommended Action
Verify the expiration dates and lot numbers. Use the wash solution for the kit and make sure that it is prepared correctly. Make sure to use the number of washes per the protocol instruction. Time each plate separately to ensure accurate incubation times, follow protocol. Maintain the lab room temperature within 20°–25°C (68°–77°F). Do not run assays under air conditioning vents or near cold windows. Make sure plates and reagents are brought up to room temperature. Keep the Reagents and plates were too cold. kit components out of the kit box for at least 1 hour before starting the assay. Reader was at wrong wavelength, Make sure the wavelength is 450 nm for the assay and read the plate again. Verify reader calibration and lamp alignment. Check records to see how many times the kit has cycled from the refrigerator. Excessive kit stress has occurred. Check to see if the kit was left at extreme temperatures for too long. Always refrigerate plates in sealed bags with a desiccant to maintain stability. Prevent condensation from forming on plates by allowing them equilibrate to room temperature (20 – 25°C / 68 – 77°F) while in the packaging.
High Background or High Optical Density (OD) Readings

Possible Causes
Recommended Action
If water quality is questionable, try substituting an alternate distilled water Substrate solution has deteriorated. Make sure the substrate is colorless prior to addition to the plate. Use the number of washes per the protocol instruction. Make sure that at least There was insufficient washing or 250 µL of wash solution is dispensed per well per wash. Verify the performance of the washer system; have the system repaired if any ports drip, dispense or Verify the reader’s performance using a calibration plate and check the lamp possibility if the OD readings were alignment. Verify the blanking procedure, if applicable, and reblank. Maintain the room temperature within 20°–25°C (68°–77°F). Avoid running assays near heat sources or in direct sunlight. Ensure that the correct reagents were used, that working solutions were prepared correctly and that contamination has not occurred. BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 9 MaxSignal® Beta-Agonist ELISA Test Kit Manual – 1009-02 High Intra-Plate Variance

Possible Causes
Recommended Action
Make sure all materials are set up and ready to use. Use a multichannel pipette to add reagents to multiple wells whenever possible. Do not interrupt while Verify pipette calibration and check that tips are on tight. Be sure all channels of the pipette draw and dispense equal volumes. There was inconsistent washing or Check performance of the wash system. Have the system repaired if any ports
High Inter-Plate Variance

Possible Causes
Recommended Action
Time each plate separately to ensure consistent incubation times. Make sure to use the number of washes per the protocol instruction. Verify Inconsistent washing occurred from performance of the wash system and have the system repaired if any ports drip or dispense/ aspirate poorly. Check the pipette calibration. Verify that pipette tips are on tight before use and that all channels draw and dispense equal volumes. Make sure to allow sufficient time for kit plates, reagents, standards and Kit plates, reagents, standards and samples come to room temperature (20 – 25°C / 68 – 77°F). Larger volumes will require longer equilibration time. If using a water bath to hasten equilibration, make sure it is maintained at room temperature; do not use a warm water bath to warm reagents, samples and kit standards. Carefully label each reagent to make sure the reagents are not intermixed. Kits with different expiration dates might generate different range of OD readings, from different kit lots, or the kits however, the relative absorbance values may very well be comparable. In were of different expiration dates. general, a value of less than 0.6 in zero standard reading may indicate certain
One or More of the Standard Curve Points Are Out of Range

Possible Causes
Recommended Action
Follow the protocol and re-run the assay. Make sure the standards are applied order or recorded in wrong position. and recorded correctly. Standards were contaminated or Use a new set of standards. Add standards to plate only in the order from low There was inconsistent washing or Perform washing consistently. Check performance of the wash system. Have the system repaired if any ports drip or dispense/aspirate poorly. Make sure all materials are set up and ready to use. Add standards to plate only Inconsistent time was taken to add in the order from low concentration to high concentration at undisrupted pace. Use a multichannel pipette to add reagents to multiple wells simultaneously. Verify pipette calibration and check that tips are on tight. Be sure all channels of the pipette draw and dispense equal volumes. BIOO FOOD AND FEED SAFETY • WWW.BIOOSCIENTIFIC.COM 10

Source: http://www.cmscorp.co.kr/product/upload/1009_02Manual.pdf