Microsoft word - golden lithium grease.doc

BOSS LUBRICANTS: MATERIAL SAFETY DATA SHEET
1. PRODUCT INFORMATION
Material:
Emergency Number:
Formula:
Chemical Name:
Date of Issue:
2. IMPORTANT COMPONENTS
3. PHYSICAL DATA
Appearance-Odor-Ph:
Melting Point:
Solubility in water:
Vapor Density (Air=1):
Evaporation Rate:
(Butyl Acetate=1)
Boiling Point:
Percent Volatile (by wt.):
Viscosity:
Vapor Pressure (mm Hg):
Specific Gravity (water=1): 0.942

FIRE AND EXPLOSION HAZARD DATA
Flash Point :
>177°C
Auto Ignition Temperature: N/A
Upper Explosion Limit (%): N/A
Lower explosion Limit (%): N/A
Extinguishing Media:

Special Fire Fighting Procedures:

Wear MSHA/NIOSH-approved, pressure-demand, self-contained breathing apparatus. Use water
spray to cool fire-exposed containers.

Unusual Fire and Explosion Hazards:
Dense smoke
BOSS GOLDEN LITHIUM GREASE
BOSS LUBRICANTS: MATERIAL SAFETY DATA SHEET
4. HEALTH HAZARD DATA
THRESHOLD LIMIT VALUE:
Effects of Exposure:
Prolonged or repeated skin contact may cause irritation

Emergency and First Aid Procedures:
Inhalation: Move subject to fresh air
Eye and Skin Contact: Flush eyes with large amounts of water for at least 15 minutes. Consult a
physician if irritation persists. Wash affected skin areas with soap and water.
Ingestion:
DO NOT give anything by mouth or induce vomiting unless directed by a physician. If unconscious, prevent aspiration of vomitus by placing face down in prone position with head turned to one side. Obtain immediate medical advice and/or attention. 5. CONDITIONS TO AVOID

Stability:
Conditions to avoid:

Hazardous Decomposition Products:

Oxides of carbon, lithium, phosphorus, sulfur, nitrogen, hydrogen, sulfide, zinc oxide,
hydrochloric acid
Hazardous Polymerization: May occur

Incompatibility (Materials to Avoid):
Strong oxiders – bromine, chromic acid
6. SPILL OR LEAK PROCEDURE

Steps to be taken in case material is released or spilled
Remove contaminated clothing and wash affected skin areas with soap and water. Wash clothing
before reuse. Dike and contain spill with inert material (sand, earth, fuller’s, etc.) and transfer liquid
and solid diking material to separate containers for recovery or disposal. Floor may be slippery – use
care to avoid fall. Keep spill out of all sewers and open bodies of water.

Waste Disposal Methods
Incinerate liquid in approved equipment. Landfill contaminated diking material according to current
local, provincial, and federal regulations.
BOSS GOLDEN LITHIUM GREASE
BOSS LUBRICANTS: MATERIAL SAFETY DATA SHEET
7. SPECIAL PRTECTION INFORMATION

Ventilation Type

Respiratory Protection
None required under normal conditions of use
Protective Gloves

Eye Protection
None normally required; splash goggles if contact is possible
Other Protective Equipment
8. STORAGE AND LABELING

Storage Temperature
Keep in cool, dry area away from heat & flame
9. TOXICITY INFORMATION

None of the components present in this material at concentrations equal to or greater than 0.1% are listed by IRAC, NTA, OSHA, or ACGIH as a carcinogen. 10. MISCELLANEOUS INFORMATION

This product does not contain any chemical in sufficient quantity to be subject to reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 & 40 CFR Part 372 The information contained herein is based on data considered accurate, however, no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use thereof. Vendor assumes no responsibility for injury or third person proximately caused by the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Additionally, vendor assumes no responsibility for injury to vendee or third persons proximately caused by abnormal use of the material even if reasonable safety procedures are followed. Furthermore, vendee assumes the risk in his use of the material. BOSS GOLDEN LITHIUM GREASE

Source: http://myclients.ca/customers/bosslubricants/website/pdfs/msds/Greases/GOLDEN%20LITHIUM%20GREASE.pdf